IMPORTANT:
About Broan Model Numbers

Some Broan model numbers have an alpha suffix.

Example: 41000-L.

It is important to refer to the exact model number with the alpha suffix when selecting parts, requesting service or speaking to a technical support representative regarding your Broan product.

Start by locating your product type:

Range Hood

Standard Under Cabinet Allure Under Cabinet Broan Elite Fashion Style Broan Elite Professional Style Island Downdraft

Ventilation Fan

Standard Bath Fan Mid-Level Bath Fan Designer Style Bath Fan Combination (Fan/Light) Bath Fan

Attic & Whole House Ventilation Fan

Powered Attic Ventilators (PAVs) Utility Ventilators

Trash Compactor

Trash Compactor

Heater

Bulb Heater Kickspace Heater Wall Heater

Standard Under Cabinet

Label Placement

The model label is located either on the right or left side wall of the range hood canopy.

View a Sample

Allure Under Cabinet

Label Placement

Remove range hood filters by pulling down on the filter tabs. The series number is located either on the back wall of the range hood housing or on the Teflon air pan. (Example...QS1, QS2 or QS3)

View a Sample

Broan Elite Fashion Style

Label Placement

Remove range hood filters. The model label is located on the underside of the canopy behind the filters.

View a Sample

Broan Elite Professional Style

Label Placement

The model label is located on the inside of left wall of the range hood canopy. Filters may need to be removed to access the label.

View a Sample

Island Downdraft

Label Placement

The model label is located on the front of unit beneath the cook top.
Cabinet drawers or shelving may need to be removed to access label.

View a Sample

Standard Bath Fan

Label Placement

Remove the grille by pulling down 2 inches. Reach behind the grille and squeeze the mounting springs to remove the grille. The model label is located in the corner closest to the outlet. Some fans may have the model stamped into the motor plate instead of a printed sticker label.

View a Sample

Mid-Level Bath Fan

Label Placement

Remove the grille by pulling down 2 inches. Reach behind the grille and squeeze the mounting springs to remove the grille. The model label is located on the underside of the motor plate.

View a Sample

Designer Style Bath Fan

Label Placement

Remove the glass lens which is attached by two leaf springs. Use a small flat head screwdriver to pry the glass lens from the grille. Screwdriver can be inserted into one of the small slots on the perimeter of the glass lens. To avoid scratching the surface of the grille the screwdriver can be wrapped in a thin cloth or tissue. Reach over lens and push in on springs to release. Grille is held by two screws along rim or a single nut in the center. The model label is located on the underside of the motor plate.

View a Sample

Combination (Fan/Light) Bath Fan

Label Placement

Remove light lens by pressing in on the sides and pulling down. Remove the light bulb. Remove the light reflector and grille by removing the center acorn nut. The model label is located on either the inside perimeter of housing or underside of motor plate.

View a Sample

Powered Attic Ventilators (PAVs)

Label Placement

The model label is located on the cover of the wiring box which is visible from the attic.

View a Sample

Utility Ventilators

Label Placement

Removed the grille by a central knob or two screws. The model may be ceiling or wall mounted. The label is located on the inside perimeter of housing opposite wiring panel.

View a Sample

Trash Compactor

Label Placement

The model may be free standing or installed under cabinet. The label is located inside on the right wall of housing at the motor level, access through rear service panel if drawer can not be removed.

All Broan 12" wide compactors use the same bags. Orders can be placed using Part #93620008 (12 pack).

All 15" wide units use bag #15TCBL (12 pack).

View a Sample

Heaters

Label Placement

Remove the grille by unhooking the springs from the housing.  The model number can be found inside the housing on a specification label.

View a Sample